Sunday, October 12, 2008

Another day in the Garage building Cafe Racer Motorcycles.

Howdy Cafe Racer fan's
Where has time gone? October already and soon it will be time for old Fatty in the ill fitting Red suit to come bombing down the flu pipe.

I have been busy as uasual, more than 20 bikes in the garage right now, but its all good.

I have also out grown the Garage at home, and now have a Workshop about 3 miles from the house.

I can bang and crash and do pretty much as much as like and when I like, as it has a security gate, so late nights are always on the cards.

Thanks for all the cool emails from you lot who check out my www.cb750cafe.com website, I try and update as much as possible, as well as email people and of course, when I can, I bung some scribble on a blog.

Today is Sunday and I headed off to the workshop as I had a 1978K series to sort out for a customers, he also dropped off a K3 that is going to be a Ful rebuild and cafe creation, but this 78 just needed abit of work to get her running.





He arrived on the bike, Broken down on the side of the road, not far from my place, I hapened to be cruisng down there and spotted the inline four sat by the side of the kerb, looking as happy as treading in Cow crap.

I pulled over and managed to start it for him, I had my shop not 2 minutes from where he was and he made it to mine.

The Motor was reving higher than the vocal chords of a choir boy.

It was running as even as a hundred Meter hurdler with a wooden leg.

He asked if I could Semi- Cafe the bike for him, and of course I said that thats no worries.

The 77 and 78 Models on a K series have them flat top carbs with the accelerator pump attached. When working correctly, they are a good set up, but right now, it was as useful as Hangman with a stuck trap door.





I pulled the tank and seat off, that 78 tank is bigger than our deficit, and I will have to sort that out too.

The seat is equipped with more padding than a teenage girls prom night.

The Carbs were nasty and I took them off and put them to one side, hoping they would run off and jump in the nearest dumpster.

I removed the intake manifolds and then I got some earlier 1969-1976 CB750K series ones, they were old ones and even though had no crack, seem to be stiffer than Grandad on Viagera.

To help get these onto the cylinder head, I used a heat gun, this softens the rubber up and easily went on the head with no issues, I slung new stainless hose clamps on and then I picked up a 1976 CB750K set of Carbs.

I had completly stripped them down to the carcass, slung the bodies and bowls wtc, into the Ultra Sonic cleaner and gave them a good cookin for about 15 minutes.

These came out hotter than a stolen car, but got all the crud off and looked great.

I fitted New main jets, and new pilots, and New O-Rings in the by passes.

Polished the float bowls and lubed up the adjusters. I bench sincronised the slides and set the floats to 24mm.

I put just a TAD of grease on the inside lip of the warm intake manifolds and the carbs literally pushed on, they plopped in easier than a small foot in a big shoe.

Now these puppies are on, I tightened the Stainless hose clamps up and then I took the old stock handlebars off, the 78K cables for the throttles are way too long, so used 1975 CB750 cables and they were perfect.

Adjusted the cables so the slides snap back nicely. Attaching the nipples to the Carbs can be a real pig, unless you have small hands, this can be a fun time for you.

After struggling, swearing and muttering stuff I did not even know I knew about, I got these to be really nice.

I fitted my Clubman bars, bunged on the switches and of course the master cylinder and, I moved the clutch cable, as it was snagging in the stock position, but now all sorted.

I fitted New fuel line too, I always use Clear line to start with, that way you can check fuel flow and make sure the air bubbles have gone, then later after a few miles I change them and add fuel filters too.

Some Gas stations pumps have more crap in them than a Stuffed Colon, so always use a filter people.

The battery was about as powerful as an Army of poofters, so that was changed for one of the new NON maintenance varieties, and this will give that motor a real kick in the guts when I hit the button.

I fitted the gas tank back on and threw the seat on the frame and kicked her in the belly, and she fired right up.

This runs good and strong right out of the gate, i was stoked.

The idle was 1500 and ran well, no popping at all, so, the bench sinc did the trick.

I shall be adding my New Yoshimura exhaust soon and will have to up jet it and then I will put it on the Dyno, just to make sure it all goes smoothly.

But, if you have a 77 or a 78K or F model and your carbs are goosed, fit earlier manifolds, cables and carbs and this will end your woes.

Also, I shall be fitting CR 29MM smooth Bores to a 1971 CB750K and will tell you how that goes.

You can change your carbs using minimal tools, its a load of bollocks when a bike company tell you it takes so many hours to fit.

You can use a 8 mm for the jets. A 10 MM for the cables and a screw driver for the clamps.

12mm will take the handlebars off too.

Snips for the fuel line, and a screw driver for the switches and a 10mm for the master cylinder.

All in all, about an hours work. If you have to alter the jets, the early carbs are so easy, just flick the snap brace and then use an 8mm wrench and out she comes, easy as that.

Remember though Gas stinks worse than grandads farts, so make sure you put rags or an old towel under the carbs when you are removing them or taking the bowls off.

Have fun with your CB750 and I will help where ever I can.

OK I am going to take that COBALT 836 out for a spin, you will like that bike, as it tured out great.






Peace and Grease

Carpy